工业电源
Click the link below to download the file.
Get your files as below link
Dowload link
24V
960W
40A
18-30 Vdc
124 x 50 x 117 mm
4.88” x 1.97” x 4.61”
0.66 kg (1.46 lb)
|
输出电流
40A
|
|
输出电压
24V
|
|
输出电压范围
17.5-29.5Vdc
|
|
输出电压调整范围
-
|
|
输出功率
960W
|
|
输出电流调整范围
|
|
最大输出电压
|
|
缓冲时间
15 s, 30 s, 45 s, 1 min, 3 min, 5 min, 10 min, 20 min, 30 min, ∞
|
|
线电压调整率
-
|
|
负载调整率
-
|
|
纹波电压
-
|
|
开机时间
-
|
|
保持时间
-
|
|
动态回应
-
|
|
电容性负载启动
-
|
|
摇控开/关
-
|
|
保护设备
-
|
|
输入输出间电压骤降
Charging Mode: 0.5V between DC input to load
Buffering Mode: 0.5V between battery to load |
|
残留波纹/PARD (20MHz)
-
|
|
残留波纹
-
|
|
最大功率
-
|
|
波纹与噪音
-
|
|
CC 型号 LED系统电压范围
-
|
|
升压时间
-
|
|
峰值功率持续时间
7 seconds
|
|
峰值功率回复时间
5 seconds
|
|
额定输入电压
24 Vdc
|
|
输入电压范围
18-30 Vdc
|
|
最大输入电压
-
|
|
额定输入频率
-
|
|
输入频率范围
|
|
额定直流输入电压
|
|
直流输入电压范围
18-30 Vdc
|
|
输入电流
Charging Mode: 1 A, 2 A, 3 A, 4 A (typ.)
|
|
输入功率（待机模式）
-
|
|
100% 负载效率
98% typ.
|
|
最大涌入电流
-
|
|
充电时间
< 4.5 hr ± 1 hr (4 A charging current for 24 V/12 AH battery)
|
|
功率因数
-
|
|
漏电流
-
|
|
额定电流
-
|
|
谐波失真总量
-
|
|
最大功率损耗
-
|
|
效率 @ 10% 负载
-
|
|
底座 / 外壳上盖
Aluminium
|
|
|
指示灯
Green LED: Battery Status
Orage LED: Diagnosis Red LED: Error |
|
|
冷却方式
Convection
|
|
|
输入端
-
|
|
|
输出端
-
|
|
|
信号端
-
|
|
|
声压级（SPL）
< 40 dBA
|
|
|
输入/输出端
-
|
|
|
信号
-
|
|
|
安装导轨
Standard TS35 DIN Rail in accordance with EN 60715
|
|
|
电线
Input / Output: AWG 18-8 (Load: 0-5 A), AWG 14-8 (Load: 5-10 A)
Battery: AWG 18-8 (Load: 0-5 A), AWG 14-8 (Load: 5-10 A) Signal: AWG 24-12 |
|
|
保护结构
-
|
|
|
端子台
Input / Output: 4 Pins
Battery: 2 Pins Signal: 8 Pins Temperature Sensor & Rx/Tx: 4 Pins (CVILUX CP3504P1H00-NH) |
|
|
重量
0.66 kg (1.46 lb)
|
尺寸
124 x 50 x
117 mm
4.88” x 1.97” x 4.61” |
|
振动测试（运行状态）
EN 60068-2-64 (Wind Power Application)
|
|
防震测试（运行状态）
-
|
|
运行温度
-40°C to +70°C
|
|
储存温度
-40°C to +85°C
|
|
功率降级
> 60°C de-rate power by 2.5% / °C (when battery is fully charged) If the battery is not fully charged at max load, it is recommended that the surrounding air temperature should not exceed 50°C.
|
|
运行湿度
5 to 95% RH (Non-Condensing)
|
|
防震测试（非运行状态）
IEC 60068-2-27, 30 G (300 m/s²) for a duration of 18 ms, 1 time per direction, 2 times in total
|
|
振动测试（非运行状态）
IEC 60068-2-6, 10 Hz to 500 Hz @ 30 m/s² (3 G peak); 60 min per axis for all X, Y, Z direction
|
|
储藏湿度
-
|
|
运行高度
0 to 6,000 m (Approvals apply only up to 5,000 m)
|
|
污染程度
2
|
|
碰撞试验（运行状态）
-
|
|
过压类别
-
|
|
Corrosion
-
|
|
过压保护
Auto Recovery
|
|
超负载/过电保护
Normal Operation: Auto Recovery
Battery Operation: Latch off |
|
过热保护
Normal Operation: Auto Recovery
Battery Operation: Latch off |
|
短路保护
Buffering Mode: Shutdown, Latch Mode
|
|
极性反接保护
-
|
|
防护等级
IP20
|
|
防震保护
Class III
|
|
输入端极性保护
Yes
|
|
电池极性保护
Yes
|
|
电池电压保护错误
Yes, 30 Vdc Max (the maximum voltage that will not cause damage to the unit)
|
|
深度放电保护
Yes (21 V typ.)
|
|
超负载保护
-
|
|
过电保护
-
|
|
内置保险丝
-
|
|
输入欠压保护
Yes
|
|
Safety Certificate
-
|
|
电气安全
CB scheme: IEC 62368-1
TUV Bauart: EN 62368-1 UL/cUL recognized: UL 62368-1 and CAN/CSA C22.2 No. 62368-1 (File No. E131881) EAC: TP TC 002/2011 |
|
CE
In conformance with EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU
|
|
医疗安全
-
|
|
电隔离
Power Port to Housing: 500 Vac
Signal Port to Housing: 500 Vac Power Port to Signal Port: 500 Vac |
|
工业控制设备
-
|
|
危险场所/ATEX
-
|
|
II 3 G ATEX 2014/34/EU
-
|
|
机器电气设备
-
|
|
用於电率安装的电气设备
-
|
|
安全特低电压
-
|
|
海事
-
|
|
材料与部件
-
|
|
隔离电阻
-
|
|
PE 电阻
-
|
|
UKCA
In conformance with Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016
|
|
国家地区证书
-
|
|
BIS
-
|
|
KC
-
|
|
Electrical Equipment for Measurement, Control, and Laboratory Use
-
|
|
ITE Safety
-
|
|
SIL3
-
|
|
排放
CE & RE
EN/BS EN 61000-6-4, EN 61204-3 |
|
抗扰度
EN/BS EN 61000-6-2, EN 61204-3
|
|
谐波电流排放
-
|
|
电压波动和闪变
-
|
|
ESD 抗扰度
-
|
|
辐射抗扰度
-
|
|
EFT
-
|
|
电涌
-
|
|
传导抗扰度
-
|
|
磁场
-
|
|
电压骤降
-
|
|
通用用途之部件供电
EN 61204-3
|
|
额定电池电压
24 Vdc, SLA Sealed lead acid battery
2 x 12 Vdc, SLA Sealed lead acid battery in series |
|
电池电压范围
21-27.6Vdc (continuously operating)
30Vdc Max (the maximum voltage that will not cause damage to the unit) 19.2Vdc Min (the voltage level of battery tol enable “Repl. BAT.” relay contact. (DRU module will not charge the battery) |
|
电池容量
3.4 AH ~ 100 AH
|
|
电池充电模式
1 A, 2 A, 3 A, 4 A (typ.) (constant current)
|
|
充电电压结束
27.6 V
|
|
电池熔断器
2 pcs in parallel; LITTELFUSE: 0257030. PXAPC, BUSSMANN: ATC-30 or equivalent (for DRN-24V7AAEN)
|
|
电池放电电压范围
21 Vdc ... 27.6 Vdc
30 Vdc Max (the maximum voltage that will not cause damage to the unit) |
|
电池充电电流
1 A, 2 A, 3 A, 4 A (typ.) (constant current)
|
|
Battery Current Consumption
< 200 mA
|
|
放电电流
-
|
|
建议充电电压
-
|
苏公网安备
32050902101200号